The Design And Construction Of A Digital Voltmeter With Seven Segment Display Using Analog-To-Digital Converter (ADC) Complete Project Material (PDF/DOC)
ABSTRACT
This project work is on Digital Voltmeter Using ICL7107. Voltmeters (voltage meter) a device used to measure voltage between given two terminals. Digital voltmeter gives a numerical display of voltage by use of an analog to digital converter. An analog-to-digital converter (ADC) is an electronic device that converts an input analog voltage or current to a digital number proportional to the magnitude of the voltage. Apart from the basic usage digital voltmeters are also employed as panel meters for automation systems and robotics. This device is built around a PIC microcontroller based digital voltmeter with LED display output.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- LIMITATION OF THE PROJECT
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- ANALOG-TO-DIGITAL CONVERTER (ADC)
- OVERVIEW OF A VOLTMETER
- TYPES OF VOLTMETER
- HISTORICAL BACKGROUND OF DIGITAL VOLTMETER
CHAPTER THREE
DESIGN METHODOLOGY
- SYSTEM BLOCK DIAGRAM
- CIRCUIT DIAGRAM OF A DIGITAL VOLTMETER WITH AVR ATMEGA8
- SYSTEM OPERATION
- CIRCUIT DESCRIPTION
- DESCRITION OF MAJOR COMPONENTS USED
CHAPTER FOUR
TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- SYSTEM SAFETY
CHAPTER FIVE
- CONCLUSION
- REFERENCES
CHAPTER ONE
- INTRODUCTION
1.2 BACKGROUND OF THE STUDY
Digital voltmeter is an instrument that measure voltage or voltage drop in a circuit. Digital voltmeter uses solid-state components and display values digitally. Typically, Digital voltmeters (digital volt meters) can be used to locate excessive resistance that may indicate an open circuit or ground. They are also used to identify low voltage or voltage drops that may indicate a poor connection. The positive lead is connected to the circuits positive side and the negative lead is connected to the circuits ground. The digital voltmeters internal resistance is the impedance, which is usually expressed in ohms per volt. This amount is relatively high in order to prevent the device from drawing significant current and disturbing the operation of the circuit being tested. The sensitivity of the Volt meter determines the range of voltages that digital voltmeters can measure.
Digital voltmeters can measure a range of alternating current (AC) voltages, direct current (DC) voltages, or both AC and DC voltages. Devices typically display between three and seven digits. Some digital voltmeters can capture minimum and maximum voltages called spike readings. Others measure the root mean square (RMS), a range of frequencies, or the signal power in decibels. Digital voltmeters are also used to monitor resistance temperature detectors (RTDs), thermocouples, transistors, and diodes. Benchtop, rack mounted, and handheld devices are commonly available. Battery powered units do not require plug-in power. Digital voltmeters with audibility continuity beep when the probes touch. Devices with analog bar graph capabilities display status readings such as battery power, signal level, and continuity.
Some digital voltmeters interface to computers and include integral monitoring software for applications such as data acquisition. Programmable devices allow users to set values that trigger monitoring routines. Data storage, logging, and removable data storage devices are often available. Some digital voltmeters allow users to adjust the sampling rate or provide internal memory. Others include an auto-ranging feature that automatically adjusts the measurement range. Output options include general-purpose interface bus (GPIB), binary coded decimal (BCD), and digital-to-analog (DA). RS232 is a standard communication protocol for serial ports. IEEE 488 is a standard communication protocol for parallel ports.
1.2 OBJECTIVE OF THE PROJECT
The main objective of this work is to design a device that will numerically display of voltage two points in an electric circuit using a IC7107.
1.3 SIGNIFICANCE OF THE PROJECT
The advantages of using IC7107 in this work are as follows:
- It has Low power consumption
- It has a better Amperes display resolution while using low value drop resistor.
- It has easy calibration, only one voltage adjust and one ampere adjust preset, no voltage out detection.
1.4 ADVANTAGES OF THE PROJECT
- They are more accurate than analog voltmeters.
- They reduce reading and interpolation errors.
- The ‘auto-polarity’ function can prevent problems from connecting the meter to a test circuit with the wrong polarity.
- Parallax errors are eliminated. If the pointer of an analog voltmeters is viewed from a different angle, you will see a different value. This is parallax error. A digital voltmeter’s numerical display solves this problem
- Digital voltmeter displays have no moving parts. This makes them free from wear and shock failures.
- The reading speed is increased as it is easier to read.
- Unlike analog voltmeters, zero adjustment is not required.
- Digital output is suitable for further processing or recording and can be useful in a rapidly increasing range of computer controlled applications.
- With the advent of Integrated circuits, the size, cost and power requirements of digital voltmeter has been drastically reduced.
- Accuracy is increased due to digital readout. You can make mistake in reading the scale in analog voltmeter, but digital voltmeter have a seven segment display to show accurate reading.
- DMMs can be used in testing continuity, capacitors, diodes and transistors. More advanced digital voltmeters can also measure frequency.
- The ‘auto-ranging’ feature of a digital voltmeter helps in selecting different measurement ranges, which can prevent damage to the meter if the wrong range is selected.
- Portable size makes it easy to carry anywhere.
- They cause less meter loading effects on the circuits being tested.
- Some advanced digital voltmeter has microprocessors and can store the readings for further processing. They have very high input impedance.
1.5 LIMITATION OF THE PROJECT
- The seven segment display’s display depends on a battery or external power source. When the battery is low, the display will be dim, making it difficult to read.
- In case of fluctuations or transients, it can record an error.
- Warming of the IC7107 during its use can change its properties leading to errors in measured value.
- There is a voltage limitation. If it is increased beyond the limit, the meter will be damaged.
- The digital nature makes it unsuitable for adjusting tuning circuits or peaking tunable responses.
- They are expensive due to high manufacturing cost.
1.6 SCOPE OF THE PROJECT
This device is built using the ICL7107. The ICL7107 is a high performance, low power, 3.5 digit analog to digital converter. The IC includes internal circuitry for seven segment decoders, display drivers, reference voltage source and a clock. The power dissipation is less than 10mW and the display stability is very high.
This digital voltmeter is simple in that the voltage to be measured is converted into a digital equivalent by the analog-to-digital converter (ADC) inside the IC and then this digital equivalent is decoded to the seven segment format and then displayed. The analog-to-digital converter (ADC) used in ICL7107 is dual slope type ADC.
1.7 PROJECT WORK ORGANIZATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to a digital voltmeter. In this chapter, the background, significance, objective limitation and problem of a digital voltmeter were discussed.
Chapter two is on literature review of a digital voltmeter. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
2.0 LITERATURE REVIEW
2.1 Introduction
The chapter presents a review of related literature that supports the current research on the Design And Construction Of A Digital Voltmeter With Seven Segment Display Using Analog-To-Digital Converter (ADC), systematically identifying documents with relevant analyzed information to help the researcher understand existing knowledge, identify gaps, and outline research strategies, procedures, instruments, and their outcomes…
This Research Work On “Design And Construction Of A Digital Voltmeter With Seven Segment Display Using Analog-To-Digital Converter (ADC)” Complete Material Can Be Downloaded Through Whatsapp, Email Or Download Link. Click The Below Button To Proceed:
This study on the Design And Construction Of A Digital Voltmeter With Seven Segment Display Using Analog-To-Digital Converter (ADC) is solely for academic research purposes only and should be used as a research guideline or source of ideas. Copying word-for-word or submitting the entire project work to your school is unethical academic behavior and “UniProjects” is not part of it.