Design And Construction Of A Solar Powered Automatic Battery Charger For 6 And 12V Lead Acid Battery

47 Pages 6,311 Words 1 – 5 Chapters Download Complete Material

The Design And Construction Of A Solar Powered Automatic Battery Charger For 6 And 12V Lead Acid Battery (PDF/DOC)

Abstract

This project focuses on the design and construction of a solar battery charger, crafted to address the increasing need for a reliable power supply to keep batteries charged. A solar battery charger is an electrical device that harnesses the photovoltaic effect to convert light energy directly into electricity. It utilizes a solar panel—a type of photoelectric cell whose electrical properties (such as current, voltage, or resistance) change with exposure to light. The panel generates an electric current when illuminated, without requiring an external voltage source. The objective of this project is to develop a solar battery charger system that receives 15V DC from the solar panel and steps it down to a safe level for charging both 6V and 12V lead-acid batteries.

Chapter One

INTRODUCTION
This chapter introduces the Design And Construction Of A Solar Powered Automatic Battery Charger For 6 And 12V Lead Acid Battery and its relevance, states the research problems, research questions, and objectives, provides a background of the study, and should also include the research hypothesis…

Chapter Two

LITERATURE REVIEW
This section presents a review of related literature that supports the current research on the Design And Construction Of A Solar Powered Automatic Battery Charger For 6 And 12V Lead Acid Battery, systematically identifying documents with relevant analyzed information to help the researcher understand existing knowledge, identify gaps, and outline research strategies, procedures, instruments, and their outcomes…

Click the button below to INSTANTLY subscribe and download the COMPLETE MATERIAL (PDF/DOC)!

Related Field(s):

Electrical Electronics Engineering (2458), Engineering (4496)

Similar Topics (Recommended)

Design And Installation Of 200 Watt Solar Power System.

44 Pages

|

5,111 Words

The 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective gadgets like cut out switches; to give the 200W expected. The solar panel was mounted outside the b […]

Production Of A High Quality Bar Soap And Compare With Detergent.

104 Pages

|

13,648 Words

The sole aim of this research work is to produce a high quality of bar soaps and compare with detergent. The major aspects of this projects deals with quality control processes in the production of a high quality bar soaps. In soap production, cold process was used and this was found out to be the most effective means of production considering several factors. In the production of bar soaps, palm kernel oil was used instead of fallow […]

Manufacture Of Ceiling Board Using Local Materials.

100 Pages

|

13,257 Words

This project “The Production of Ceiling Board from Local Raw Materials” was carried out basically using raw materials which was sourced locally. These raw materials are found to be very much in abundance. Some are materials sourced from the ground and others are from agricultural wastes. Three different types of ceiling boards were produced, their difference being in the type of fibre that was used. The fibres used for this different […]

Design And Construction Of A DC To AC Power Inverter Incorporated With An Automatic Switch Over Battery Charger.

31 Pages

|

3,579 Words

INTRODUCTION All modern engineering system include certain aspects of control systems at some point in their broadcast sense, control engineering and the associated theory are concerned with the means by which systems may be made to behave an a desired way. The system on this thesis is a DC – AC converter, which is an apparatus which is used for conversion of Direct Current to Alternating Current or signal. In our country, this equipme […]

Design And Construction Of A Battery Charger With Over-Charge Cut-Off.

49 Pages

|

7,070 Words

A battery charger is an electrical device employed for charging batteries. These batteries that are usually charged by battery charger are the storage batteries also known as “accumulator” the battery charger changes. The alternating current forms the power line into d.c suitable for charging. When the battery is fully changed, is up to it’s maximum, 12 volt, the charger with automatically cut-off with the help of the contact relay […]

Design And Construction Of A 12 Volts Automatic Battery Charger.

45 Pages

|

5,319 Words

A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating current form the power line into d.c suitable for charging. When the battery is fully changed, is up to it’s maximum, 12 volt, the charger with automatically stop changing wi […]

Design And Construction Of A Battery Cage.

48 Pages

|

5,206 Words

Battery or bird cages are homes for domesticated birds. Birds require a house in which they can fly and have some freedom but still ensure they do not fly away. Bird cages are constructed to be large enough to accommodate the motion and daily activities of domesticated birds. This work was carried out to build a bird cage using available materials.

This Study On The Design And Construction Of A Solar Powered Automatic Battery Charger For 6 And 12V Lead Acid Battery Is Relevant To Students And Researchers In Electrical Electronics Engineering
Engineering And Related Fields.